Ingredients:
>> Analog board
>> Main board with screen
>>Resistors:
> 100 Kohm resistor*2
> 1.8 Mohm resistor*1
> 200 Kohm resistor*2
> 2 Mohm*1
> 20 Kohm*1
> 300 ohm *3
> 180 ohm *2
> 120 ohm *2
> 1.1 Kohm*3
>> 2 volt zener diode
>> HF chokes: 100 microHenry *2
>> Anything you want color led
>> 5 – 30 picoFarad *1 and 2 -6 picoFarad *1 capacitor trimmers
>> Ceramic capacitors:
> 0.1 microF
> 220 picoF
> 3 picoF
> 500 picoF
>> 2.54 mm rightangled pin header
>> 100 microF / 16 V *5 electrolytic capacitors
>> Slide switches
>> Pin headers ( male and female)
>> Tact switches
>> Hook probes
And iron, solder wire, multimeter, flush cutter, tweezers and acrylic cover ( transparent is the best by the way)
You can solder everything to the analog board ( photo up – below )
You can attach the main board to the analog board and use an usb cable with micro- plug to power.
Okay, done! Have fun!
>> Analog board
>> Main board with screen
>>Resistors:
> 100 Kohm resistor*2
> 1.8 Mohm resistor*1
> 200 Kohm resistor*2
> 2 Mohm*1
> 20 Kohm*1
> 300 ohm *3
> 180 ohm *2
> 120 ohm *2
> 1.1 Kohm*3
>> 2 volt zener diode
>> HF chokes: 100 microHenry *2
>> Anything you want color led
>> 5 – 30 picoFarad *1 and 2 -6 picoFarad *1 capacitor trimmers
>> Ceramic capacitors:
> 0.1 microF
> 220 picoF
> 3 picoF
> 500 picoF
>> 2.54 mm rightangled pin header
>> 100 microF / 16 V *5 electrolytic capacitors
>> Slide switches
>> Pin headers ( male and female)
>> Tact switches
>> Hook probes
And iron, solder wire, multimeter, flush cutter, tweezers and acrylic cover ( transparent is the best by the way)
You can solder everything to the analog board ( photo up – below )
You can attach the main board to the analog board and use an usb cable with micro- plug to power.
Okay, done! Have fun!
🐁🐁🐁🐁🐁🐁🐁🐁🐁🐁🐁🐁🐁🐁🐁🐀🐀🐀🐀🐀🐀🐀🐀🐀🐀🐀🐀🐀
⚡️ Ingredients for Niminy home-made Tesla Coil⚡️
>>1*BD24 3C transistor
>>1*Small heat sink - 15*10*20
>>1*10 kohm resistor
>>1*PCB board
>>1*coil
>>3 mm led (no matter which color)
>>1*DC 005 seat
>>1*105 monolithic capacitor
>>1*Self locking switch-8*8
>>1*bubble-(aka. neon lamp)
>>4*mini screw
>>1* screw-3*6-
>>6*M2 double pass copper column
>>1*adaptor/9~12 volt battery
All of them of ingredients is soldered to the main PCB board except for screws.
Have fun!🥒🐀✨
>>1*BD24 3C transistor
>>1*Small heat sink - 15*10*20
>>1*10 kohm resistor
>>1*PCB board
>>1*coil
>>3 mm led (no matter which color)
>>1*DC 005 seat
>>1*105 monolithic capacitor
>>1*Self locking switch-8*8
>>1*bubble-(aka. neon lamp)
>>4*mini screw
>>1* screw-3*6-
>>6*M2 double pass copper column
>>1*adaptor/9~12 volt battery
All of them of ingredients is soldered to the main PCB board except for screws.
Have fun!🥒🐀✨